Alternative Materials For Aircraft Wings

Alternative Materials For Aircraft WingsFor this report I have chosen to enquiry and find an alternative worldly for aircraft wings, before long the stuff and nonsense being on aircraft wings is aluminum metal series 2000, unique(predicate)ally 2024 as this stretch consists of about 4.5% copper, 1.5% magnesium, 0.6% manganese with traces of other precise voiceicles permitted, and the remainder atomic number 13.1The alternative material must be capable of achieving all the characteristics of atomic number 13 corrupt 2024, in time be light in load and preferably within the m integritytary value region of materials currently utilize.Aims and objectivesThe aim of this report is discuss how alternative materials support be produced to manufacture a new luminosity aircraft wing. In bless to do this the new material must be capable of withstanding eminenter(prenominal) stress loads, be light in weight and preferably upset in cost. Also, manufacturing technique must b e looked into with respect to machin dexterity of material, cost of machines, and repairing material. underway materials in exerciseAluminium alloy 2024This is example in the gentle wind manufacturing as it has the right properties essential to meet the demands. The principle alloying element apply is copper. This alloy requires solution heat treatment to obtain its silk hat properties when the alloy has been through the solution heat treatment process the mechanized properties become corresponding to and sometimes exceed those of mild steel. To further profit the mechanical properties of aluminum alloy 2024, an artificial ageing process is apply this method of treatment increases the egress aptitude. Once the aluminium alloy has been do, the properties obtained ar luxuriously distinctiveness to weight ratio, as well as keen moil confrontation. Though this is non wieldable and has average machin dexterity. Due to poor erosion resistance the alloy is comm neve rtheless cladded with clarified aluminium, however, this does usually reduce the frighten away resistance of the alloy.Aluminium alloy 2024 consists of about 4.5% copper, 1.5% magnesium, 0.6% manganese with traces of other specific elements permitted and the remainder is aluminium.Mechanical properties of aluminium 2024The mechanical properties of 2024 depend on the annoyance of the material.2024-0This form of alloy has no heat treatment (annealed). It has an ultimate bendable potence of 207-220 MPa to a greater extent than wear bearing of 96 MPa. This form of alloy as well as has an e massiveation factor of 10-25%.2024-T3This form of alloy has been solution case-hardened and strain hardened with the ultimate flexible potence is between cd-427 MPa and yield strength of 369-276 MPa with an elongation of 10-15%.New materials to consider atomic number 22This metal has a juicyschool strength to weight ratio, a relative density of 4.5 which is 60% heavier than aluminium ho wever, it is in two ways as hefty.Titanium has splendid corrosion resistance properties this is receivable to the oxide adopt which forms. Titanium is not normally susceptible to stress, fatigue, intergranular or galvanic corrosion, putting or localised attack. However, under certain great deal it roll char in air, therefore in order to prevent a chemical reaction with oxygen or nitrogen it whitethorn be treated with chloride gun in order to form a preservative coating of atomic number 22 dioxide.Titanium normal alloying elements include aluminium, chromium, iron, manganese, molybdenum and vanadium.Titanium and its alloys argon classed in 3 categoriesAlpha (A) Wieldable, tough, strong two enthusiastic and cold and foul to oxidisation.Beta (B) Excellent bend ductility, strong both hot and cold however vulnerable to contamination.Combined (C) combination of alpha and beta with comprised performance, strong cold and warm precisely shaky when hot, dainty forgabil ity, good bendibility moderate contamination resistance. The melting point of atomic number 22 is 1668 degrees Celsius and has pocket-sized thermal conductibility and a basic base co efficient of expansion. Its uplifted temperature properties ar however disappointing. the ultimate yield strength falls rapidly supra 425 degrees Celsius and atmospheric oxygen and nitrogen absorbent above 540 degrees Celsius makes the metal brickly and worthless after a long term exposure. thereof it is unaccompanied useful for short durations, high temperatures applications where strength is not important much(prenominal)(prenominal) as air conditioned firewalls.When scating with titanium extra economic aid must be taken when making due to its extreme work hardening properties. E.g. centre drill should be used prior to drilling as centre punch this material would harden the metal, causing hindrance when drilling.CompositeA composite material consists of 2 or much distinguishable mate rials whose mechanical properties compliment each other although maintain their adjourn identities, unlike alloy.The reason the composite materials be used on an aircraft and their strength to weight ration and corrosion resistance. built plastics ar much lighter than metals. If the metal part puke be as much as 25 times heavier than an equivalent composite part, however that composite part must be as strong and durable as the original.Therefore reinforced plastics must have real good strength, affluentness and w acuteness resistance.Strength- this is the ability of a material to support a load without breaking.Stiffness- this is the ability of material to support a load without bending too much.Impact- this is the ability of a material to withstand resistance concussion without shattering.The types of composites to consider for this render would be, film over reinforced plasticAramid partsCarbon fibresGlass Reinforced Fibres (GRFs)Glass Reinforced Fibres are currently us ed on aircraft for radomes (the fairings which cover radiolocation antennas and must be transparent to radio waves). The fibre folderol is used for keep for thermosetting resins in aircraft applications is available as a cloth in m whatever different weights and lifts as a loose of fibre looking glass. When unite, the fibre and resin GRF.For applications which require the most strength it is necessary to use uni-directional glass tape. Whereas twist glass cloth has better shaping properties and high strength.There are many types of Glass Reinforced Fibres used, and the main ones used in the airmanships manufacture areA Glass- standard soda glass has a high alkaline content which absorbs moisture which increases degrading of material and corrosion. This leaks to resins deterioration. The main use for this is for windows.C Glass- high resistance to corrosive material. It is normally produced and used barely as a surface matt to reduce cost.D Glass- with a humble di-electric constant this type of glass is used for radomes.E Glass- with junior-grade alkali content and good resin adhesion properties where used in air conditioning.Styles of interweave clothThe most common style used is the excess weave where the distort and wraft threads cross alternately. The strength of weave fabrics in comprised due to the foul pre- buckling already present in the fabric. Fibres usually produce their greatest strength when they are perfectly straight. Due to the high frequency of over and under weaving of the threads the strength is decreased in plain weave. This is where t willing weave and satin weave come in as it is high pliable and stronger than the plain weave style.This table shows a equality of the properties of common weaves used in aerospaceStability ability of the weave to hold together when cut.Drape ability of the cloth to follow a complex shape.Porosity an recitation of the amount of resin required to soundly wet the cloth.Smoothness surface finish of the cloth.Balance a comparison between the warp and weft direction.Symmetry the weave pattern.Crimp an indication of the amount or frequency of bend in the yarns.5Aramid fabricsAramid fibres withal cognize as Kevlar is make from aromatic polyamide, a type plastic similar to nylon.The properties includeHigh tensile strength and resistance to impact of any composite reinforcing fibre.Stiffer than glass but only half as stiff as century fibre.40% lighter than glass fibre10x stronger than aluminiumUp to 400% stronger than similar glass reinforced laminates.Up to 20% stronger than comparable carbon enforced laminatesAramid fibres have truly high impact strength with the damage confined to small areas. Due to this, Aramid can be used in areas prone to stone and runaway debris damage, so this could be useful for use on aircraft wings.However, Aramid fibres have lower densification strength than carbon, it absorbs moisture more readily than glass or carbon, also Aramid det eriorates in strong sunlight. Aramid is more difficult to cut, drill, sand accordinglyce either glass or carbon, it also does not give clean edges.Aramid fibres do not resist flame well and burn through more quickly than other fibres. Resin adhesion is also lower, delamination being one of the ways in which it absorbs impact energy.Carbon fibresCarbon fibres are made from carbon and are black in colour carbon fibres were first used on air conditioning in the 1980s.The fibres are manufactures by the controlled heating of POLYCRILONITRILE (PAN), polythene or rayon fibres are pre-oxidised at 200-300 degrees Celsius for 1 minute then carbonised at 1200 degrees the graphitised at 2000 to 3000 degrees Celsius. This removes the hydrogen, nitrogen and oxygen leaving long oriented carbon chains.The fibres are sometimes surface oxidised, this improves their building characteristics and sized, this then reduces the build up of static electricity and improves bonding.Carbon fibres are avail able in forms basic groups and produced at different graphitisation temperature and defined by tensile modulesStandard modules (high strength)Intermediate modules (high stiffness)High modulusUltra high modulus.All forms of carbon fibre are stiffer than glass fibres, however only standard modulus is stronger than glass fibres in tension. The higher modulus fibres are very brittle and are not suitable for general aeronautical use.Aluminium- atomic number 3This is part of series 8000 of aluminium alloys. Having low density, the lithium reduces the weight of alloy while offering strength which is comparable to series 7000 (also a higher strength aluminium alloy made from zinc) and competes with composite materials. Aluminium lithium also has high specific modulus and excellent fatigue and cryogenic pettishness properties.The disadvantages of aluminium lithium is reduces ductility and recrudesce toughness in short transverse direction also the read to cold work this alloy to obtain pe ak properties and further fatigue part extension rates when cracks are micro morphologic small.By using aluminium lithium in aircraft wings will enable low costs flying as it saves weight and displace consumption costs, also this would lead to a reduction in fear costs.Fatigue affects materials after long term exposure to cyclic fill up using aluminium lithium is stronger than carbon fibre therefore aluminium lithium can withstand fatigue longer. Aluminium lithium is currently being used on the Airbus A380, and under investigation with Boeing.Analysis contemporary materialThe current material used for aircraft wings is aluminium. This material is currently used to construct aircraft wings. This is because this material is light in weight, easy to machine, easy to shape also this form of aluminium is easy to machine in order to meet required standards such as high yield strength in ratio with the weight, and also aluminium 2024 also has very good fatigue resistance. However, t his form of aluminium alloy has poor corrosion resistance therefore in order to protect against this the alloy is cladded with uncontaminated aluminium, this however has a downside to it as it further reduces the fatigue resistance of the alloy.The advantages of aluminium areLight weightEasily shaped/cast/ fabricateGood electrical conductorGood thermal conductor simple to machineThe disadvantages of aluminium areExpensive to refine (must be make by electrolysis of fused salts)Poor chemical resistance (acids and base)Loses strengths when heatedCladded with 6.25mm of pure aluminium, if that is broken, the material begins to corrode fast.Alternative materialsThe alternative materials that can be used areTitaniumThis metal has a high strength to weight ratio, a relative density of 4.5 which is 60% heavier than aluminium however it is twice as strong.Titanium has excellent corrosion resistance properties this is due to the oxide film which forms. Titanium is not normally susceptible to stress, fatigue, intergranular or galvanic corrosion, putting or localised attack. However, under certain circumstances it will burn in air, therefore in order to prevent a reaction with oxygen or nitrogen it may be treated with chloride gas in order to form a protective coating of titanium dioxide.Titanium and its alloys are classed in 3 categoriesAlpha (A) Wieldable, tough, strong both hot and cold and repellent to oxidisation.Beta (B) Excellent bend ductility, strong both hot and cold however vulnerable to contamination.Combined (C) Combination of alpha and beta with comprised performance, strong cold and warm but weak when hot, excellent forgability, good bendibility moderate contamination resistance. The melting point of titanium is 1668 degrees Celsius and has low thermal conductibility and a low co efficient of expansion. Its high temperature properties are however disappointing. the ultimate yield strength falls rapidly above 425 degrees Celsius and atmospheric oxygen a nd nitrogen absorbent above 540 degrees Celsius makes the metal brittle and worthless after a long term exposure.The model type of titanium to use on an aircraft wing would be the combined (C) class as it does meet to requirements for an aircraft wings. However, the major drawback for this material is when working with titanium extra care must be taken when making due to its extreme work hardening properties.The advantages of titanium areLightweight backbreakingAble to withstand high temperaturesCorrosion resistantThe disadvantages of titanium areExpensiveProcess for forming and joining titanium are complex and dear(predicate)Glass Reinforced FibresThe fibreglass is used for reinforcement for thermosetting resins in aircraft applications is available as a cloth in many different weights and weaves as a loose of fibreglass. When combined, the fibre and resin Glass Reinforced Fibre.For applications which require the most strength it is necessary to se uni-directional glass tape. Whe reas woven glass cloth has better shaping properties and high strength.There are many types of Glass Reinforced Fibres used, and the main ones used in the aviations industry areA Glass- standard soda glass has a high alkaline content which absorbs moisture which increases degrading of the material and corrosion. This leaks to resins deterioration. The main use for this is for windows.C Glass- high resistance to corrosive materials. It is normally produced and used only as a surface matt to reduce cost.D Glass- with a low di-electric constant this type of glass is used for radomes.E Glass- with low alkali content and good resin adhesion properties.Styles of woven fabricThe most common style used is the plain weave where the warp and wraft threads cross alternately. The strength of woven fabrics in comprised due to the severe pre- buckling already present in the fabric. Fibres usually produce their greatest and strength when they are perfectly straight. Due to the high frequency o f over and under weaving of the threads the strength in reduced in plain weave. This is where twill weave and satin weave come in as it is high pliable and stronger than the plain weave style.The advantages of GRF areStrength and resistance can be adjusted during the manufacturingImpact resistanceLightweightHeat resistantWill not corrodeAble to withstand all but the strongest forms of acid and alkaliThe disadvantages of GRF areEasy to damageExpensive machines required to produceRequires special storageAlthough glass reinforced fibres are very good with respect to the advantages and disadvantages, it may not be the precedent prime(prenominal) to use as a material for an aircraft wing as it would be expensive to produce and store, and also there are many types of glass reinforced fibres but not a particular type could be chosen because there is not a material which is specifically ideal and has all the characteristics required for an aircraft wing.AramidAramid fibres have very high impact strength with the damage confined to small areas. Due to this, Aramid can be used in areas prone to stone and runaway debris damage, so this could be useful for use on aircraft wings.However, Aramid fibres have lower compression strength than carbon, it absorbs moisture more readily than glass or carbon, also Aramid deteriorates in strong sunlight. Aramid is more difficult to cut, drill or sand then either glass or carbon it also does not give clean edges.The advantages of Aramid areHigh tensile strengthImpact resistantTen times as strong as aluminium400% stronger than GRF20% stronger than carbon fibreThe disadvantages of Aramid areLow compressive strength then carbonAbsorbs moisture more than glass or carbon fibreDeteriorates in sunlightDifficult To Cut, Drill or SandDoes not give clean cut edgesAramid is a very good material to use, however it is important that when making aircraft skin the wings must be smooth and easy to machine, due to Aramid not being able to take into account these key features, it should be used for this part of the skin, however, Aramid should be considered for the leading edge of the aircraft wings, because it has the characteristics required to withstand stone and runaway debris damage.Aluminium- LithiumHaving low density, the lithium reduces the weight of alloy while offering strength which is comparable to series 7000 (also a higher strength aluminium alloy made from zinc) and competes with composite materials. Aluminium lithium also has high specific modulus and excellent fatigue and cryogenic toughness properties.The disadvantages of aluminium lithium is reduces ductility and expose toughness in short transverse direction also the need to cold work this s alloy to obtain peak properties and reanimate fatigue crack extension rates when cracks are micro structural small.Fatigue affects materials after long term exposure to cyclic onus using aluminium lithium is stronger than carbon fibre therefore aluminium lithium can withstand fatigue longer.The advantages of aluminium-lithium are10% denser than aluminium 2024Lightweight10 15% higher modulus than aluminium 2024Excellent fatigue and cryogenic toughness propertiesHigher stiffnessSuperior fatigue crack growth resistanceThe disadvantages of aluminium-lithium areReduced ductilityLow fracture toughnessAluminium- lithium is a new concept within the aviation industry which allows the industry to progress in a new direction, this allows an aircraft to be light, efficient yet have the same amount of or more power to transport both passengers and freight. Also, with aircraft being so light it may allow even large aircrafts then the currently produced Airbus A380, and Boeing 787 to be produced. Aluminium- lithium the characteristics required for use on aircraft wings and therefore should be considered for this project. consequenceIn conclusion aluminium- lithium should be used as it has the properties such as light weight and excellent fatigue and cryoge nic toughness properties required for an aircraft wing and carry the weight loaded on to the matte hence enabling aircrafts to be designed on a bigger scale in order to carry more cargo and passengers as is proven by the production of the Airbus A380 which is one the largest planes in production braggart(a) a higher power to weight ratio.The A380s wing is sized for a maximum take-off weight (MTOW) over 560 tonnes in order to accommodate these in store(predicate) versions, albeit with some strengthening required. The stronger wing (and structure) will be used on the A380-800F freighter. This common design approach sacrifices some fuel efficiency on the A380-800 passenger model, but Airbus estimates that the size of the aircraft, coupled with the advances in technology will provide lower operating costs per passenger than the 747-400 and older 747 variants.6 acknowledgmentBooks UsedBritish Airways applied science Training Part 66 faculty 6- Materials and Hardware. Published 14/02 /2005. Issue 1.Introduction to aircraft design. John P. Fielding. ISBN 0521657229Aircraft Design Projects For Engineering Students. Lloyd R. Jenkinson. Dr. Jim Marchman. ISBN 0750657723Websites usedhttp//www.sciencedaily.com/releases/2007/09/070926094727.htmhttp//en.wikipedia.org/wiki/Al-Liwww.soton.ac.uk/jps7//manufacturing/aluminum-lithium.docwww.keytometals.com/Article58.hthttp//en.wikipedia.org/wiki/Airbus_A380cite_note-norris_wagner_book-12Appendix 1